Cutting Flexible Circuit Board, Cutting Metal, Ceramics, Silicon Wafer FPC Laser Cutting Machine Linear Motor Cross Working Platform Can Be Spliced UV Cutting

 

Ultraviolet FPC laser cutting machine
FPC shape laser cutting machine
Ultraviolet FPC laser cutting machine adopts ultraviolet laser, cold light source, laser cutting heat affected area is especially small to 10 m, suitable for FPC soft plate, hard combined plate shape laser cutting, dividing plate, drilling hole, cutting edge neat round, smooth, no burr, no glue overflow.

 

 

 

sample display:  









The service zone:
1.Pre-sale problem

A.Ultraviolet laser cutting materials are available?
Ultraviolet laser cutting machine adopts 355nm cold light source and is processed by breaking the molecular bonds of materials. It belongs to cold processing category with small thermal impact area and fine cutting. It is widely used in the material industry, mainly in electronics, photovoltaic, communication, medical treatment, aerospace and other fields.

Ultraviolet laser cutter materials include common industrial application processing, graphene, carbon fiber cutting, cutting PET, PI, cutting, cutting ultra-thin metal cutting (copper foil, aluminum foil, gold foil, etc.), ceramic cutting, FPC/PCB cutting and so on, also including some polymer materials, composite materials, etc., welcome everyone to come to consult, yuan lu photoelectric provide free proofing services.


B.What materials can femtosecond laser equipment process?
Femtosecond laser processing equipment has a wide range of applications, including material cutting, etching, drilling, marking, surface bionic treatment, groove cutting, marking, micro-structure treatment and so on. The applicability is very wide, including ultra-thin metal, inorganic non-metallic material, composite material, polymer material, such as glass marking, metal foil cutting, ultra-thin copper foil punching, polymer material surface treatment, etc., welcome everyone telephone consultation understanding


C.Can ITO on PET laser-etch a line width of 7 microns?
Wuhan Yuanlu photoelectric laser etching equipment adopts ultra-short pulse femtosecond laser, which can realize ITO etching on PET flexible substrate, the minimum line width is less than 7 microns, the minimum spacing is less than 7 microns, welcome everyone to make samples and test.


D.Can copper foil be cut with laser?
Yuanlu photoelectricity ultraviolet laser cutting machine can be used for copper foil cutting and drilling within 2 microns to 200 microns, cutting edge cutting smooth, no burr, no deformation, welcome to test proofing


2.After using
A.Why laser marking machine to play out the two-dimensional code is very clear, high contrast, but bar code gun sometimes can be swept out, sometimes can not be swept out?
Usually, the cause is not the effect of laser marking itself, but the incorrect scanning Angle of barcode gun. If the code is read vertically, the reading rate will be low, and most barcode guns have a low tolerance rate. Therefore, a certain Angle is required to read, so the reading rate will be higher.

So you can try to adjust the scanning Angle of the scanning gun to solve the problem. Generally speaking, the best solution is to add coaxial camera identification under the scanning head of marking machine, and automatic identification after typing, which is more accurate and saves time.


B.How to deal with the dust of ULTRAVIOLET laser cutting PCB?
Ultraviolet laser cutting PCB does not have dust, but it will produce smoke. The way to deal with the smoke is to remove it through the dust extraction device coaxial with the laser vibrator, and honeycomb adsorption platform is adopted at the bottom to ensure the flatness of the board on the one hand, and solve some smoke problems on the other hand.

In cutting aluminum substrate, copper substrate is coaxial laser pay gas, such as nitrogen, oxygen, air or argon as an auxiliary gas, on the one hand to blow away the slag, on the other hand, according to other different protection or combustion, oxidation prevention and other functions.


C.Laser marks on both sides of the edge of the word is not clear, why?
Hello! Preliminary judgment you is to use laser marking machine lens scanning range is 110 * 110 mm, that is to say within the effective range by laser are normal, black, clear handwriting, but after more than 110 mm, while scanning lens can also have a certain ability to work, but the deflection of light energy is not strong, and exceed the scope of the won't scan it.

Take a simple example. When we turn on a flashlight, the Angle of divergence has a great relationship with the luminous distance. The white paper near the flashlight will be completely covered by the light, but when it shines on the wall a few meters away, a piece of white paper cannot be covered. The scope of the scanning lens is as if it were covered by this white paper.Therefore, the effective solution is to replace the large lens, such as 140*140mm scanning lens, which can solve the problem.

In addition, the scope of the scanning lens is related to the power of the laser, etc. Blindly increasing the scanning range power cannot keep up with, which will also cause unsatisfactory marking effect.


D.Laser marking process has been continuous light out of what reason?


According to yuanlu photoelectric analysis, there are the following reasons:

1. The wrong switch sequence may lead to continuous light emitting. The correct starting sequence is: total power = > computer = > marking software = > chiller = > Q driver = > laser power = > etc. After the READY light on the excitation power = > press the RUN key to start = > galvanometer power switch. The shutdown sequence is reversed.
2. The ON, OFF and RUN switches ON the old Q drive are wrong; ON is the forced light command; OFF is the forced turn OFF laser command; the correct way is to select RUN.
3. The board card is broken, please replace it.
4.Q switch is not properly adjusted. In normal condition, it will emit light when marking. In case of no marking, Q switch should lock the laser.
5. Computer or control system problems. Replace or reinstall the system.
6. Drive Q is broken. Replace drive Q.
7.Q switch is broken, replace Q switch (this is rare, generally speaking, Q switch is broken, Q driver will alarm)

Need laser marking machine friends can contact yuan Lu photoelectric
 

Yuan Lu photoelectric after - sales service commitment:

Wuhan Yuanlu Photoelectric Technology Co., Ltd. adheres to customer as the center, and provides you with perfect installation, commissioning, training, maintenance and other pre-sales and after-sales services.

 

1. Pre-sales service

Before signing the contract, the company provides customers with various production process plans, technical consultation of laser equipment, sample sample, equipment selection and other services.

 

2. Installation and debugging

According to the contract, our company can safely deliver the equipment to the installation site designated by the user within the specified time, and can provide technical service engineers for on-site installation.The technical service engineer will complete the installation and debugging of the machine in time for the user's use under the condition that the user has the basic equipment for installation and debugging, so as to ensure that the installation and debugging site environment is neat, clean and orderly.

 

3. After-sales training

The company provides free technical training. After the completion of installation and debugging, the company will provide technical training for the buyer's operators at the buyer's site or the seller's domestic training and maintenance center until the operators can basically use the equipment normally. The main training contents are as follows:

• Training on the use of common drawing software;

• Training on the use of machine control software;

• Train on/off machine operation procedures;

• Training on the meaning of panel and software control parameters and the scope of parameter selection;

• Basic cleaning and maintenance of machines;

• Common hardware fault handling;

• Problems to be noticed in operation;

In addition, it also provides users with technical support for the products it produces

 

4. Equipment maintenance

Company commitment: free equipment maintenance for one year, lifetime maintenance.

No matter whether the equipment is under warranty or not, the company will provide after-sales service in a timely manner. After receiving the warranty fax from the buyer, the after-sales service personnel of the company will ensure to reply the processing result within 1 hour.

Free technical consultation, software upgrade and other services.

When the equipment warranty expires, lifelong maintenance services, only for accessories charged cost.

Throw out a wide range of hardware and software support after the warranty expires.